Tasmota - 4 relay board

[Yocee84]

Yes, i has Gateway, same as Vamp.

[Vamp]

Thank you for your feedback. If you want to control these devices from an external network, you will need a Tuya gateway.

I have a gateway. A Matter ZigBee Hub (THP10-Z-X)

ID: bf211f6985abed2bbensnl

[Vamp]

I try to reconnect the device. here the new ID-s:

Matter网关兜底(bfb4524uyrhcsehb)
W20-UBEA 4(bf0bd94b089a068d288ztg)
W20-UBEA 2(bf6eeffd17e40c0b30cgze)
W20-UBEA(bf9a102e30cedfe039xziz)
W20-UBEA 3(bfeaf6f502ac01b543kuks)

[huangxh]

Thank you for your feedback. If you want to control these devices from an external network, you will need a Tuya gateway.

I have a gateway. A Matter ZigBee Hub (THP10-Z-X)

ID: bf211f6985abed2bbensnl

you can update the gateway to version 1.13.4, then test again.thanks.

[Vamp]

@huangxh

updated info:

I successfully update the gateway. Now i able to switch on the relay remotely, but the state are not refresh in app. It also the same problem in local network (the old gateway firmware, locally work well)

I re-connect the device, here the new IDs:

W20-UBEA 3 (bf255a5a6445c714a3niqw)
W20-UBEA (bf7ef5a8b731e8f696ryft)
W20-UBEA 2 (bfa4945e715d0fb8df4ess)
W20-UBEA 4 (bfbfa957fcfa302607cxoe)
Matter网关兜底 (bfc6311on1yieb1t)

Further test:

I make two tap to run automation.

1. tap it to on one of relay on tasmota matter board
2. tap it to off one of relay on tasmota matter board

Both of them are working! so it send the on / off comand. also say that if i run "on" automation, i not get confirmation but i run "off" i get it:

see the pictures:

[huangxh]

@huangxh

updated info:

I successfully update the gateway. Now i able to switch on the relay remotely, but the state are not refresh in app. It also the same problem in local network (the old gateway firmware, locally work well)

I re-connect the device, here the new IDs:

W20-UBEA 3 (bf255a5a6445c714a3niqw)
W20-UBEA (bf7ef5a8b731e8f696ryft)
W20-UBEA 2 (bfa4945e715d0fb8df4ess)
W20-UBEA 4 (bfbfa957fcfa302607cxoe)
Matter网关兜底 (bfc6311on1yieb1t)

Further test:

I make two tap to run automation.

1. tap it to on one of relay on tasmota matter board
2. tap it to off one of relay on tasmota matter board

Both of them are working! so it send the on / off comand. also say that if i run "on" automation, i not get confirmation but i run "off" i get it:

see the pictures:

Could you test it again: turn off/on the device, then let me know the test time. Thank you.

[Vamp]

Do it now.

2025.may.23

22.26 UTC

[huangxh]

Do it now.

2025.may.23

22.26 UTC

Sorry, it was the weekend the other day and the log was overwritten. Could you try again today? Due to the time difference, you could try earlier in the morning there, while I should be able to check it immediately in the afternoon here.